Open circuit and short circuit test of a single phase transformer pdf

Posted on Saturday, April 24, 2021 10:20:35 AM Posted by Quesugigar - 24.04.2021 and pdf, for pdf 5 Comments

open circuit and short circuit test of a single phase transformer pdf

File Name: open circuit and short circuit test of a single phase transformer .zip

Size: 2916Kb

Published: 24.04.2021

To determine the circuit constant, efficiency and regulation of a transformer, without actually loading the transformer, we perform Open-Circuit and Short-Circuit tests. These tests give more accurate result than compared with the fully loaded transformer. And the power consumption in these tests is minimal as compared with the transformer's output on full load. A voltmeter V, an ammeter A, and a wattmeter W are connected in the low voltage lv side of transformer.

Studies on performance parameters of a practical transformer for various utilizations

Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising. If you continue browsing the site, you agree to the use of cookies on this website. See our User Agreement and Privacy Policy. See our Privacy Policy and User Agreement for details. Published on Nov 28,

This work has been conducted at the electrical machines lab in European University of Bangladesh EUB for both the experimental and analytical determination of the performance parameters of the transformer for practical utilization. Insulation resistance test was done to check the insulation level, which can identify the presence of major faults. The vector group tests also performed to identify the group numbers for various connection facilities of practical transformer. The subject under consideration was a 1. This type of research work like 1. This study will be the guide line for practical utilization of transformer for different purposes. This is a preview of subscription content, access via your institution.

Open Circuit & Short Circuit Tests on Transformers

Facebook Twitter. These tests are very convenient as they provide the required information without actually loading the transformer. Further, the power required to carry out these tests is very small as compared with the full-load output of the transformer. These tests consist of measuring the input voltage, current and power to the primary first with secondary open-circuited open-circuit test and then with the secondary short-circuited short circuit test. This test is conducted to determine the iron losses or core losses and parameters R 0 and X 0 of the transformer. In this test, the rated voltage is applied to the primary usually low-voltage winding while the secondary is left open circuited. The applied primary voltage V 1 is measured by the voltmeter, the no load current I 0 by an ammeter and no-load input power W 0 by watt meter as shown in Fig.

The open-circuit test , or no-load test , is one of the methods used in electrical engineering to determine the no-load impedance in the excitation branch of a transformer. The no load is represented by the open circuit, which is represented on the right side of the figure as the "hole" or incomplete part of the circuit. The secondary of the transformer is left open-circuited. A wattmeter is connected to the primary. An ammeter is connected in series with the primary winding. A voltmeter is optional since the applied voltage is the same as the voltmeter reading.

open circuit and short circuit test on single phase transformer

One winding of the transformer whichever is convenient but usually high voltage winding is left open and other is connected to its supply of normal voltage and frequency. A wattmeter W, voltmeter V and an ammeter A are connected in low voltage winding in the present case. With normal voltage applied to the low voltage winding, normal flux will be set up in the iron core, hence normal iron losses will occur which is recorded by wattmeter. As the no- load current in low voltage winding is small, cu loss is negligibly small in low voltage winding and nil in high voltage side. Hence, the wattmeter reading represents practically the core loss under no-load condition.

The open circuit and short circuit test are performed for determining the parameter of the transformer like their efficiency, voltage regulation, circuit constant etc. These tests are performed without the actual loading and because of this reason the very less power is required for the test. The open circuit and the short circuit test gives a very accurate result as compared to the full load test. The purpose of the open-circuit test is to determine the no-load current and losses of the transformer because of which their no-load parameters are determined.

If it is used for converting power from a high voltage to a low voltage, it is called a step-down transformer. The conversion efficiency of a power transformer is extremely high and almost all of the input power is supplied as output power at the secondary winding. The transformer may be represented by the equivalent circuit shown in figure 3.

Em Lab-II Manual

These two transformer tests are performed to find the parameters of equivalent circuit of transformer and losses of the transformer. Open circuit test and short circuit test on transformer are very economical and convenient because they are performed without actually loading of the transformer. Open circuit test or no load test on a transformer is performed to determine 'no load loss core loss ' and 'no load current I 0 '. The circuit diagram for open circuit test is shown in the figure below. Usually high voltage HV winding is kept open and the low voltage LV winding is connected to its normal supply. Now, applied voltage is slowly increased from zero to normal rated value of the LV side with the help of a variac. When the applied voltage reaches to the rated value of the LV winding, readings from all the three instruments are taken.

One winding of the transformer whichever is convenient but usually high voltage winding is left open and other is connected to its supply of normal voltage and frequency. A wattmeter W, voltmeter V and an ammeter A are connected in low voltage winding in the present case. With normal voltage applied to the low voltage winding, normal flux will be set up in the iron core, hence normal iron losses will occur which is recorded by wattmeter. As the no- load current in low voltage winding is small, cu loss is negligibly small in low voltage winding and nil in high voltage side. Hence, the wattmeter reading represents practically the core loss under no-load condition.


Aim: To determine Regulation and Efficiency of a single phase transformer by open circuit (o.c.) and short circuit (s.c.) tests. Apparatus: . Range/Rating. Make. 1.


COMMENT 5

  • Hindi to arabic learning book pdf free download nespresso vertuoline manual pdf english Roslyn B. - 24.04.2021 at 21:44
  • Experiment No: 2. Open circuit and short circuit tests on single phase transformer. 1 Aim. • To understand the basic working principle of a transformer. • To obtain. Polixena F. - 25.04.2021 at 11:19
  • To browse Academia. Scott L. - 29.04.2021 at 13:15
  • It is possible to predict the performance of a transformer at various loadings by knowing all the equivalent circuit parameters. Cleodora A. - 29.04.2021 at 14:52
  • We conduct open circuit and short circuit test on single phase transformer to determine the efficiency and regulation of a transformer on any load condition and at any power factor. Jucvolida - 02.05.2021 at 11:59

LEAVE A COMMENT